Goto Section: 15.235 | 15.237 | Table of Contents
Revised as of November 24, 2020
Goto Year:2020 |
§ 15.236 Operation of wireless microphones in the bands 54-72 MHz, 76-88
MHz, 174-216 MHz, 470-608 MHz and 614-698 MHz.
(a) Definitions. The following definitions apply in this section.
(1) Wireless Microphone. An intentional radiator that converts sound
into electrical audio signals that are transmitted using radio signals
to a receiver which converts the radio signals back into audio signals
that are sent through a sound recording or amplifying system. Wireless
microphones may be used for cue and control communications and
synchronization of TV camera signals as defined in § 74.801 of this
chapter. Wireless microphones do not include auditory assistance
devices as defined in § 15.3(a) of this part.
(2) 600 MHz duplex gap. An 11 megahertz guard band at 652-663 MHz that
separates part 27 600 MHz service uplink and downlink frequencies.
(3) 600 MHz guard band. Designated frequency band at 614-617 MHz that
prevents interference between licensed services in the 600 MHz service
band and channel 37.
(4) 600 MHz service band. Frequencies in the 617-652 MHz and 663-698
MHz bands that are reallocated and reassigned for 600 MHz band services
under part 27.
Note to paragraphs (a)(2), (3) and (4): The specific frequencies will
be determined in light of further proceedings pursuant to GN Docket No.
12-268 and the rules will be updated accordingly pursuant to a future
(5) Spectrum Act. Title VI of the Middle Class Tax Relief and Job
Creation Act of 2012 (Pub. L. 112-96).
(b) Operation under this section is limited to wireless microphones as
defined in this section.
(c) Operation is permitted in the following frequency bands.
(1) Channels allocated and assigned for the broadcast television
(2) Frequencies in the 600 MHz service band on which a 600 MHz service
licensee has not commenced operations, as defined in § 27.4 of this
chapter. Operation on these frequencies must cease no later than the
end of the post-auction transition period, as defined in § 27.4 of this
chapter. Operation must cease immediately if harmful interference
occurs to a 600 MHz service licensee.
(3) The 657-663 MHz segment of the 600 MHz duplex gap.
(5) The 614-616 MHz segment of the 600 MHz guard band.
(6) Prior to operation in the frequencies identified in paragraphs
(c)(2) through (5) of this section, wireless microphone users shall
rely on the white space databases in part 15, Subpart H to determine
that their intended operating frequencies are available for unlicensed
wireless microphone operation at the location where they will be used.
Wireless microphone users must register with and check a white space
database to determine available channels prior to beginning operation
at a given location. A user must re-check the database for available
channels if it moves to another location.
(d) The maximum radiated power shall not exceed the following values:
(1) In the bands allocated and assigned for broadcast television and in
the 600 MHz service band: 50 mW EIRP
(2) In the 600 MHz guard band and the 600 MHz duplex gap: 20 mW EIRP.
(e) Operation is limited to locations separated from licensed services
by the following distances.
(1) Four kilometers outside the following protected service contours of
co-channel TV stations.
Type of station Protected contour
(dBu) Propagation curve
Analog: Class A TV, LPTV, translator and booster Low VHF (2-6) 47
High VHF (7-13) 56 F(50,50)
UHF (14-51) 64 F(50,50)
Digital: Full service TV, Class A TV, LPTV, translator and booster Low
VHF (2-6) 28 F(50,90)
High VHF (7-13) 36 F(50,90)
UHF (14-51) 41 F(50,90)
(2) The following distances outside of the area where a 600 MHz service
licensee has commenced operations, as defined in § 27.4 of this chapter.
Type of station Separation distance in kilometers
Base 7 0.2
Mobile 35 31
(f) The operating frequency within a permissible band of operation as
defined in paragraph (c) must comply with the following requirements.
(1) The frequency selection shall be offset from the upper or lower
band limits by 25 kHz or an integral multiple thereof.
(2) One or more adjacent 25 kHz segments within the assignable
frequencies may be combined to form a channel whose maximum bandwidth
shall not exceed 200 kHz. The operating bandwidth shall not exceed 200
(3) The frequency tolerance of the carrier signal shall be maintained
within Â±0.005% of the operating frequency over a temperature variation
of âˆ’20 degrees to +50 degrees C at normal supply voltage, and for a
variation in the primary supply voltage from 85% to 115% of the rated
supply voltage at a temperature of 20 degrees C. Battery operated
equipment shall be tested using a new battery.
(g) Emissions within the band from one megahertz below to one megahertz
above the carrier frequency shall comply with the emission mask in § 8.3
of ETSI EN 300 422-1 V1.4.2 (2011-08), Electromagnetic compatibility
and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to
3 GHz frequency range; Part 1: Technical characteristics and methods of
measurement. Emissions outside of this band shall comply with the
limits specified in section 8.4 of ETSI EN 300 422-1 V1.4.2 (2011-08).
[ 80 FR 73069 , Nov. 23, 2015, as amended at 81 FR 4974 , Jan. 29, 2016;
82 FR 41559 , Sept. 1, 2017]
Goto Section: 15.235 | 15.237
Goto Year: 2020 |
CiteFind - See documents on FCC website that
cite this rule
Want to support this service?
Report errors in
this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please
help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
Helping make public information public